Delivered to your address (DAP) in 8–11 working days from our warehouse in Slovenia · export price without VAT; export customs clearance at a fixed fee; import VAT and duties are paid by the buyer

SKU: 750040_01

€59

Export price without VAT • Goods delivered for export are invoiced without VAT

In stock

🔒 Secure checkout • PCI‑DSS compliant

    • Export price without VAT Goods delivered for export are invoiced without VAT
    • CE-compliant Machines from ISO-certified manufacturers
    • Secure payment Card, PayPal or bank transfer
    • In stock Delivered to your address (DAP) in 8–11 working days from our warehouse in Slovenia · export price without VAT; export customs clearance at a fixed fee; import VAT and duties are paid by the buyer
    • 12-month warranty Register it in the customer portal · service and spare parts from us
    • Returns and complaints No fee if the product is faulty, damaged in transit or not as ordered

    10,000+ products sold across Europe 30+ years of team experience

    Squeegee rubber strips for the J45

    Rear squeegee rubber strip for the J45 floor scrubber, rolledThese are the squeegee rubber strips for the J45 floor scrubber: both the front and rear strips fit the squeegee and collect water after the brush, allowing the suction motor to remove it from the floor.

    The front strip is 850 × 47 × 3.2 mm, the rear strip is 900 × 50 × 4.2 mm, both made for the 800 mm squeegee on the machine.

    The strips are consumable parts and wear out over time in the same way as the brush, so it is advisable to keep a spare set available to avoid downtime when a strip becomes worn. The brush wears at the same time, so inspect it when replacing the strips. Once the edge is worn and no longer forms a seal, it is time to fit new strips. The front and rear strips differ in size and are not interchangeable.

    When replacing a strip, switch off the machine, raise the squeegee, open the buckle (buckle 2 for the front strip, buckle 1 for the rear), remove the steel plate and fit the new strip. Keep the strips clean by wiping them with a damp cloth, as any debris underneath will leave water behind. The squeegee height can be adjusted using the washers beneath the castor supports, and the squeegee can be levelled using the nut on the squeegee screw, so that the strips press evenly against the floor.

    Front squeegee rubber strips for the J45 floor scrubberThese strips are essential for leaving the floor dry behind the machine. If a strip is worn or soiled, the 500 W suction motor will pull in air rather than water, leaving the surface damp and potentially hazardous.

    Each strip is secured to the squeegee with a steel plate and buckle, so it can be replaced easily without the need for special tools.

    Where the J45 squeegee strips are used

    J45 squeegee rubber strips are used in industrial and commercial cleaning where floors must be left dry and safe after scrubbing. Typical environments include warehouses, production facilities, logistics hubs, retail outlets, healthcare sites, schools and any premises with regular machine floor cleaning. The strips are suitable for both in-house cleaning teams and contractors working across multiple sites.

     

    Technical specifications

    Product squeegee rubber strips, front and rear
    For machine J45 floor scrubber
    Front strip (L × W × T) 850 × 47 × 3.2 mm
    Rear strip (L × W × T) 900 × 50 × 4.2 mm
    Squeegee width 800 mm
    Suction motor 500 W
    Mounting steel plate and buckle
    Box (L × W × H) 15 × 15 × 15 cm

     

    What the strips do

    • Dries the floor in a single pass. The strips channel water directly to the suction point, leaving the surface dry.
    • Designed for the J45. Cut to fit the 800 mm squeegee on the J45, both front and rear positions.
    • Improves floor safety. Wet floors are slippery; a well-sealed squeegee ensures the area is dry and safe to walk on.
    • Easy to replace. Simply undo the buckle, remove the steel plate, fit the new strip and secure it again.
    • Both strips included. The set allows you to renew both squeegee strips at once.
    • Intended as a consumable. The strips wear out like the brush; keeping a spare set ensures your machine continues to dry effectively.

     

    Included in the set

    • Absorbent squeegee strips for the J45, front and rear
    • Front strip: 850 × 47 × 3.2 mm
    • Rear strip: 900 × 50 × 4.2 mm
    • Fits the 800 mm J45 squeegee
    • Secured by a steel plate and buckle
    • Can be changed without special tools
    • Consumable part

     

    How to replace the strips

    1. Switch off the machine and raise the squeegee.
    2. Open buckle 2 for the front strip or buckle 1 for the rear, and remove the steel plate holding the strip in place.
    3. Remove the worn strip and fit the replacement.
    4. Refit the steel plate and fasten the buckle; if the plate is loose, adjust the nut at the top of the buckle.
    5. Lower the squeegee and test it on a damp area: the floor behind should be left dry.

     

    Maintenance and adjustment

    • Squeegee height. If the strip presses down too much, the machine is harder to move; if too high, water remains. Adjust the height using the washers beneath the castor supports.
    • Level squeegee. If one side is lower, loosen the nut on the squeegee screw, level it, then retighten the nut.
    • Keep strips clean. Wipe the strips with a damp cloth; any debris underneath will leave water behind.
    • After use. Raise the squeegee and clean away any dirt; clean the squeegee, strips and brush every three days.
    • Secure fitting. If a strip is not firmly fixed, air can enter and the machine will not dry the floor properly.
    • When to replace. Once the edge is worn and no longer forms a seal, it is time to fit new squeegee rubber strips.

     

    Before you purchase

    J45 floor scrubber, compatible with these squeegee rubber stripsThe price is shown on this page. Squeegee rubber strips are selected for the machine, so please check the following before purchasing:

    • The machine. These squeegee rubber strips are designed for the J45. The J25, J85 and J115 require different strips; always order according to your machine model.
    • Front and rear. The front squeegee strip measures 850 × 47 × 3.2 mm, while the rear strip is 900 × 50 × 4.2 mm, so they are not interchangeable.
    • A spare set. It is advisable to keep an extra set of squeegee rubber strips in stock to avoid downtime when a strip becomes worn.
    • The brush too. The brush wears at the same time as the squeegee rubber strips; inspect it when replacing the strips.
    • Delivered to your address (DAP) · export price without VAT; export customs clearance at a fixed fee; import VAT and duties are paid by the buyer. Supplied in a box measuring 15 × 15 × 15 cm, weighing approximately 1 kg.

    Additional information

    Weight 1.0 kg
    Dimensions 0.15 × 0.15 × 0.15 m

    What is the main purpose of the SMITH J45 Industrial Floor Cleaner?

    It is intended for efficient cleaning of industrial floors, removing dirt and debris using absorbent rubber strips.

    Can the absorbent rubber strips be replaced?

    Yes, the rubber strips are replacement parts and can be changed to maintain the best cleaning performance.

    Which floor types can the SMITH J45 be used on?

    It is appropriate for a range of industrial floor surfaces, such as concrete, tiles, and sealed floors.

    How do the absorbent rubber strips enhance cleaning?

    They soak up liquids and help remove stubborn dirt, improving overall cleaning effectiveness.

    Are the absorbent rubber strips for the SMITH J45 compatible with other industrial cleaning machines?

    The absorbent rubber strips are made specifically for the SMITH J45 model and may not be suitable for other machines.

    What upkeep is necessary for the absorbent rubber strips?

    It is advisable to check and clean the strips regularly, and to replace them once any wear becomes apparent.

    Are the materials in the rubber strips resistant to chemicals?

    Yes, the rubber strips are manufactured from materials that withstand typical industrial cleaning chemicals.

    Is the SMITH J45 suitable for use in wet areas?

    Yes, the absorbent rubber strips are specifically made to perform well in damp or wet environments.

    How robust are the absorbent rubber strips during intensive industrial operation?

    They are built for longevity, though replacement will be needed from time to time, depending on the level of use.

    Summary

    • Absorbent rubber strips suitable for J45 industrial floor scrubbers
    • Fits the J45 floor cleaner squeegee assembly
    • Front rubber strip dimensions: 850 x 47 x 3.2 mm
    • Rear rubber strip dimensions: 900 x 50 x 4.2 mm
    • Produced from a robust absorbent rubber blend
    • Promotes effective water collection after cleaning
    • Enables rapid and even floor drying
    • Preserves consistent suction efficiency throughout use
    • Helps minimise slip hazards in professional settings
    • Allows for swift replacement without specialist tools
    • Intended for professional and business applications
    • Delivered to your address (DAP) · export price without VAT; export customs clearance at a fixed fee; import VAT and duties are paid by the buyer – one year warranty

    Regulatory Compliance

    EU Guarantee

    Product Documentation

    Technical Data Sheet (PDF)

    Please sign in to access the complete technical data sheet.

    User Guide (PDF)

    Accessible for registered customers. Versions and tracking included.

    Product Certification Documents (PDF)

    Please log in to access the complete technical data sheet and CE certificate.

    J45 rear rubber strip

    Scrubber Dryer Squeegee Rubber SMITH J45 – Absorbent Rubber Strips

    €59

    In stock

    In stock

    Supplying premium goods throughout Europe

    Discover how our products are utilised by customers across the United Kingdom.